Engineering Calculator 02 · Modeled on 85T/120T LSR & 650×650 mm HCR Platens

LSR vs. HCR Process, 650×650 Platen Cavity & Weight Calculator

Estimate part gram weight, see how many cavities fit inside Youbang’s 200–250T heated platens (up to 650×650 mm), and compare pilot HCR compression against automated 85T/120T LSR injection.

Enter Bounding Dimensions & Volume

1. Part Envelope & Project Profile

2. Instant Engineering Estimate (SG ~1.15 g/cm³)

200–250T Solid HCR Compression Molding

Medium annual volume with ribbed geometry fits multi-cavity 200–250T HCR compression for optimal tooling ROI.

Est. Silicone Part Weight~80 gSilicone elastomer mass only
650×650 mm Platen Max Cavities12 – 16 穴Includes mold-frame & tear-edge margins
Recommended Tooling TierTier B · Multi-Cavity Production Mold7–15d T1 sample · 15–30d mass run
Post-Cure & QC Protocol~200 °C × 4 h Post-Cure + 2D FAIOptional SGS / TÜV lab test (~10d)
Send Calculated Spec for Exact 24h Quote * Note: Platen cavity count and gram weight are geometric estimates; final cavity economics and piece pricing are confirmed against your 3D STEP CAD.

Engineering Decision Matrix

When to Choose HCR Compression vs. LSR Injection Molding

Comparison CriterionHCR Solid Compression (10 × 200–250T)LSR Liquid Injection (85T & 120T)
Press Fleet at Youbang10 Hydraulic Presses (200–250T, heated platens 400×400 to 650×650 mm)2 Closed-Loop 2-Part LSR Presses (85T & 120T)
Upfront Tooling Investment1.0× Baseline (lowest entry cost; ideal for pilot launch & large mats)~2.2×–3.5× Baseline (precision cold-deck / metered injection steel)
Piece-Price Economics at ScaleCompetitive for medium batches & heavy/wide-area partsLowest unit cost at 30,000+ pcs/yr via automated short cycles & minimal trim labor
Minimum Wall & Flash Control0.40 mm limit (0.50 mm stable) · Standard hand/cryo tear-edge trim0.25 mm limit (0.30 mm stable) · Virtually flash-free parting lines
Color & Compound ChangesFast changeover on 2 open mixing mills; easy multi-Pantone SKU splitsBest suited to dedicated clear/translucent or high-volume single-color runs

Sourcing & Tooling FAQ

Key Answers Before Tooling

Covering CAD readiness, custom MOQ evaluation, free 3D fit checks vs. T1 silicone samples, NDA protection and mold ownership.

Have a part-specific question?

Send your drawing or sample photo directly to Zhou Li’s engineering desk for a 24h DFM reply.

How accurate is the silicone gram-weight calculation before 3D CAD is finalized?

Cure-grade silicone elastomers have a typical specific gravity of ~1.10–1.20 g/cm³ (we model ~1.15 g/cm³ as baseline). Once you share a STEP or IGES 3D model, our CAD software computes exact net volume to the tenth of a gram for precise piece pricing.

Why doesn’t a 650×650 mm press platen hold edge-to-edge cavities across the entire 650 mm width?

Mold bases require perimeter steel rails, guide pillars, vacuum channels and tear-edge overflow grooves, leaving roughly ~520–550 mm of active cavity layout span plus inter-cavity steel walls to prevent mold-plate deflection under 200–250 tons of clamp force.

Can we launch with a low-cavity HCR pilot mold and upgrade to multi-cavity LSR later?

Yes—many DTC and hardware brands validate market demand with a 2- or 4-cavity HCR compression tool first, then commission a high-cavitation HCR or LSR production mold once annual volume exceeds 30,000+ units.

B2B Factory Direct · 24h Engineering & Tooling Review

Want Our Mold Designers to Calculate Exact Cavitation From Your STEP File?

Upload your 2D/3D drawings or dimensioned sketch for an itemized mold + unit-price breakdown within 24 hours.

✓ NDA available before CAD exchange✓ Eligible for 1–3 free 3D fit prototypes✓ Paid molds 100% owned by customer

Direct Dongguan Engineering Desk

  • Accepts STEP / IGES / PDF / DWG or sample photos
  • New mold T1 typically 7–15 days · Mass run 15–30 days
  • Direct Tel / WeChat: +86 185 6655 6911 (Zhou Li)