Custom Silicone Case Study · EV & Power Electronics · Multi-Lip IP67 Flange Gasket

22% Gland Squeeze & Low-Set Platinum Seal for an EV Charging Inlet Housing

Developing a flanged multi-lip perimeter gasket for an outdoor EV charging inlet milled in anodized aluminum—holding ±0.05 mm critical bead geometry, shifting parting seams off working sealing ribs, and maintaining low compression set across −40 °C to +150 °C cycling from 100-pc pilot verification.

22% Gland Squeeze & Low-Set Platinum Seal for an EV Charging Inlet Housing
Multi-lip flanged orange silicone IP67 perimeter gasket seated inside CNC aluminum EV inlet housing beside loose orange and black seals
Molding & Tooling5-Axis EDM + Low-Set Platinum HCR/LSR
Gland Compression Fit22% Squeeze · ≤80% Groove Volume Fill
Critical Bead Datum±0.05 mm Lip Height · Clean Edge Trim
Post-Cure & Pilot200 °C × 4–6h Bake · 100 pcs Trial Entry
Before Tooling

Eliminating Corner Extrusion Bunching, Parting-Line Wicking & Thermal Compression Set

Perimeter aluminum connector housings exposed outdoors undergo sub-zero cold snaps, under-hood heat soaking, and tight four-bolt corner tightening that pinch flat single-rib gaskets out of square grooves or open capillary water tracks across horizontal flash seams.

  • Prevent compressed elastomer from overfilling rounded 90-degree housing corners and pinching inside flange bolts.
  • Keep mold parting lines cleanly offset along outer retention ears rather than across vertical water-blocking seal crests.
  • Hold long-term rebound force without permanent groove flattening after sustained hot-cold cycling and 200 °C × 4–6h post-curing.
Sample Approval

Clean Bolted Corner Seating, Repeatable Field Rebound & Smooth 100-Pc Validation

T1 flanged gaskets drop straight into anodized CNC housing grooves without twist or corner wave, meet 2D optical FAI bead datums cleanly (±0.05 mm tight sealing profile; ±0.1–0.2 mm flange perimeter), and support buyer pilot environmental validation from 100 pcs.

  • T1 2D optical cross-section bead height, groove width, and Shore 55A uniformity reports on both orange and black lots.
  • Customer-assembled aluminum flange IP immersion & cold/heat cycle validation samples from 100 pcs production cavities.
  • 36-month master compound batch CoA retention log and serialized 100% customer-owned steel mold storage.

Tooling and Process Steps

Twin-Bead Groove Relief, Offset Self-Trimming Shutoff & 2D Optical Datum QC

Engineers reworked cross-section contact geometry before machining multi-cavity steel in our 5-axis CNC/EDM toolroom, trading broad flat crushing walls for balanced twin sealing ribs inside a 78%–80% groove volume envelope.

01

Twin-Lip Profile tuned for 22% Vertical Deflection & ≤80% Groove Fill

Replaced a wide square strip with dual rounded top sealing beads plus side friction nibs—cutting bolt clamp force while keeping ~20% void groove relief for thermal expansion at high ambient heat.

02

Offset 5-Axis Mirror EDM Shutoffs Away from Top Sealing Crests

Placed mold parting tangents along the outer side positioning step with clean self-trim tear relief so radial sealing lips present uninterrupted smooth molded elastomer to mating faces.

03

Low-Set Platinum Gum, 200 °C × 4–6h Circulating Bake & 2D Optical FAI

Molded low-compression-set 55A safety-orange platinum elastomer, completed 200 °C × 4–6 hours hot-air post-curing across 6 circulating ovens, and verified bead height (±0.05 mm) on 2D optical projectors ahead of buyer water-pressure assembly runs.

Twin-Bead Groove Relief, Offset Self-Trimming Shutoff & 2D Optical Datum QC
Dimensional measurement equipment

B2B Factory Direct · initial response within 24 hours

Upload Mating Housing Groove CAD & Temperature / IP Targets

Share gland cross-section dimensions, bolt clamping limits, and operating fluid/heat cycling specs for a first engineering reply within 24 hours.

✓ Trial from 100 pcs · Standard 1,000 pcs or $2,000 USD✓ Free 3D-printed fit prototypes before steel tooling✓ Paid molds 100% owned by customer
View helpful RFQ inputs
  • Enclosure groove STEP drawing + mating cover flatness & stop height
  • Operating thermal window, fluid splashes & high-visibility Pantone requirement
  • Pilot launch order volume (supported from 100 pcs onward)

Send Your Project Brief or CAD

For confidential drawings, sign the mutual NDA before uploading the files.

Only rights holders or their authorized representatives may upload files. We keep inquiries and attachments to prepare quotes and follow up on your project.

Prefer email or files > 20 MB? Send directly to zhouli@ybsilicone.com · Privacy Policy