Representative Engineering Program · Pet Enrichment · High-Tear HCR Compression

Filleted Clean-Release Grooves & Anti-Bite Tooling for a Pet Lick Mat & Slow Feeder Set

Helping a North American e-commerce pet brand differentiate from catalog listings with a custom 60 Shore A high-tear platinum silicone lick mat and maze bowl bundle—eliminating dishwasher food trapping, corner chewing, and ocean-freight suction deformation.

Filleted Clean-Release Grooves & Anti-Bite Tooling for a Pet Lick Mat & Slow Feeder Set
Bowl, textured food surface and bowl-underlay mat
Molding Process200–350T HCR Compression Molding (Up to 650×650 mm Platens)
Material & DurometerHigh-Tear Platinum Food-Grade Silicone · 60 Shore A
Key QC FocusR1.5 mm Pocket Fillet Demold Integrity & Flat Suction Skirt Plane
Sampling & Lead TimeT1 in 7–15 days · Mass run 15–30 days

Representative Engineering Program: Illustrates Youbang’s typical mold-shutoff, elastomer compounding and QC workflow for this part geometry. Client-funded molds and proprietary CAD remain strictly protected under NDA.

01 · Engineering Challenge

Preventing Trapped Food Paste, Edge Chewing & Warped Suction Cups

Audit of competing marketplace listings revealed three structural failure modes driving negative buyer reviews on standard pet mats:

  • 90-Degree Pocket Residue: Sharp internal pocket corners trapped dried peanut butter and wet food paste even after residential high-temperature dishwasher cycles.
  • Corner Curling & Tear Propagation: Thin 3 mm low-durometer mats lifted at the corners, allowing dogs to grip the rim and tear off elastomer fragments.
  • Ocean-Freight Suction Distortion: Loose polybag packing compressed underside mini suction cups during palletized FBA transit, ruining floor adhesion.
02 · QC & Deliverables

Clean Dishwasher Release & Compression-Free Fulfillment Delivery

After T1 sample approval and carton drop checks, bulk sets shipped directly into North American fulfillment centers with repeatable batch traceability.

  • Tear-resistant 60 Shore A mats and upright maze bowls verified via 2D optical profile checks and 3× Shore A durometer inspections
  • Flush, unwarped underside micro-suction arrays protected by rigid corrugated divider packaging
  • Platinum-cured raw material CoAs, post-cure logs, and SGS/Intertek FDA 21 CFR 177.2600 food-contact test coordination (~10 days)

03 · Tooling & Process Execution

60 Shore A Fumed-Silica Formulation, R1.5 mm Root Fillets & Recessed Suction Grid

Our Dongguan mold design and compounding teams optimized groove draft geometry, border stiffness, and flat-pack carton protection.

01

3D Pocket Prototyping & Tear-Strength Durometer Selection

Delivered free 3D-printed geometry prototypes (client paid freight) once CAD and quote were confirmed to verify four-zone pocket depths and maze wall heights, alongside existing-mold 50A–70A silicone samples that locked in a high-tear 60 Shore A platinum compound.

02

Full R1.5 mm Internal Fillets & 5.5 mm Beveled Anti-Bite Frame

Replaced sharp 90° groove roots across cross-ribs, honeycombs, and nubs with R1.5 mm full radii for clean dishwasher flushing and tear-free press demolding, framed by a 5.5 mm beveled perimeter border and recessed underside micro-suction cups.

03

Ventilated Post-Curing & Divider-Supported FBA Cartons

Molded on 200–350T compression presses followed by ~200 °C × 4–6 h ventilated post-curing for odor-free food contact, then packed flat inside partner-supplied corrugated insert boxes with FNSKU barcodes so suction skirts remained uncompressed.

60 Shore A Fumed-Silica Formulation, R1.5 mm Root Fillets & Recessed Suction Grid
Youbang molding workshop

B2B Factory Direct · initial response within 24 hours

Launching a Proprietary Silicone Pet Mat, Slow Feeder, or Travel Bowl?

Send the actual component drawing, use conditions and approval limits so this representative program can be adapted to your requirements.

✓ Trial from 100 pcs · Standard 1,000 pcs or $2,000 USD✓ Free 3D-printed fit prototypes before steel tooling✓ Paid molds 100% owned by customer

Helpful RFQ Inputs

  • 3D STEP / IGES files or dimensioned sketches for mat, slow feeder, or collapsible bowl
  • Preferred Shore A firmness, Pantone colorways, and underside suction or flat backing
  • E-commerce or retail box specs, barcode labeling, and estimated initial order volume