Custom Silicone Case Study · Respiratory Accessories · Platinum LSR Overmolding on Clear PC

Precision Dual-Lip LSR Cushion Overmolding on Polycarbonate Mask Frames

Overmolding a frosted 30 Shore A platinum liquid silicone dual-lip face seal cushion directly onto buyer-supplied optical polycarbonate (PC) mask frames—holding a 0.30 mm feathered inner rolling membrane, clear snap tabs, and silane-primer peel integrity.

Precision Dual-Lip LSR Cushion Overmolding on Polycarbonate Mask Frames
Clear polycarbonate respiratory mask frame overmolded with a translucent dual-lip feathered platinum LSR cushion
Process Route85T–160T Closed-Loop LSR Overmolding
Feathered Seal Wall0.30 mm inner rolling lip · 30 Shore A
Tooling Lead Time7–15 days via in-house 5-axis CNC/EDM
Clean AssemblyISO 13485:2016 · 600 m² clean packing
Before Tooling

Holding Uniform 0.30 mm Lip Roll Without Crushing Clear PC Frames

Respiratory cushion cushions fail when LSR clamping forces crack buyer polycarbonate shells, primer overspray clouds transparent viewports, or thick parting seams irritate nasal bridges.

  • Isolate clamping shutoffs cleanly on non-optical perimeter lands without stressing rigid PC headgear clips.
  • Mask optical PC ports before thin silane primer application so cured seals bond tight yet latches stay optically clear.
  • Control venting across the deep nasal pocket so the 0.30 mm rolling inner membrane fills completely with zero air-trap voids.
Sample Approval

Batch Traceability & Buyer Regulatory Handoff

Shipped lots travel with upstream platinum LSR CoAs, PC incoming frame checks, pull-adhesion logs, 2D contour checks, and 36-month lot traceability under Youbang’s ISO 13485:2016 silicone molding scope (62026Q00072R100); buyer manages finished-device regulatory clearance.

  • 2D optical dimensional reports verifying feathered 0.30 mm seal profile symmetry and PC clip clearance.
  • Destructive cushion-to-polycarbonate peel records demonstrating cohesive elastomer tearing along primed ridges.
  • 600 m² dust-controlled double-PE thermal bag packaging ready for downstream clinical device assembly.

Tooling and Process Steps

Precision Masked Priming, Vented CNC Cores & Clean Double-PE Pack

Our 5-axis CNC/EDM toolroom builds stepped shutoff cradles around the actual buyer PC lot, pairing masked silane priming with cold-runner platinum LSR injection and clean dual-pouch sealing.

01

PC Insert Gauging & Masked Silane Priming

Incoming buyer PC shells pass 2D optical frame checks before molded silicone masking plugs shield clip ports during thin silane primer coating and controlled thermal activation.

02

Vacuum-Assisted Platinum LSR Dual-Lip Injection

Primed PC frames load into 5-axis machined S136 shutoff cradles on an 85T–160T LSR press, filling a gradient 0.30 mm rolling face membrane cleanly without flashing onto clear ports.

03

Sub-HDT Bake Check, Tensile Pull & 600 m² Clean Pack

Thermal conditioning matches polycarbonate heat limits verified at T1, followed by destructive cushion-to-PC pull checks, ultrasonic pure-water wash, backlit visual screening, and double-PE bag sealing.

Precision Masked Priming, Vented CNC Cores & Clean Double-PE Pack
Closed-loop 85T-160T horizontal liquid silicone rubber injection press and sealed A/B metering drums

B2B Factory Direct · initial response within 24 hours

Share Your Mask Shell CAD & Lip Wall Targets

Upload PC/PA shell 3D STEP drawings, target cushion Shore A, and pilot trial or volume plan. Youbang engineers reply within 24 hours with shutoff cradle and masking feedback.

✓ Trial from 100 pcs · Standard 1,000 pcs or $2,000 USD✓ Free 3D-printed fit prototypes before steel tooling✓ Paid molds 100% owned by customer
View helpful RFQ inputs
  • Buyer hard-shell frame 3D STEP + exact polycarbonate or resin grade
  • Target cushion durometer (e.g. 20–40 Shore A) and feathered lip wall thickness
  • Pilot run quantity (trial from 100 pcs) and clean packaging specification

Send Your Project Brief or CAD

For confidential drawings, sign the mutual NDA before uploading the files.

Only rights holders or their authorized representatives may upload files. We keep inquiries and attachments to prepare quotes and follow up on your project.

Prefer email or files > 20 MB? Send directly to zhouli@ybsilicone.com · Privacy Policy