Youbang · B2B Custom Silicone Manufacturing · Dongguan

Custom Silicone Keypads, Seals & Overmolded Equipment Parts

Dongguan Youbang Silicone Products Co., Ltd. engineers custom tactile keypads, conductive/EMI gaskets, primer-overmolded frames, and protective terminal sleeves around your mating enclosure and PCB drawings. Across ten 200–250T compression presses (400×400 to 650×650 mm platens) and 85T/120T LSR machines, we process standard, conductive, and flame-retardant silicone (0–80 Shore A) alongside confirmed EPDM, NBR, and FKM elastomers.

304 stainless steel and glass-filled nylon frames overmolded with matte black/gray silicone seals alongside jet-black P+R conductive carbon-pill keypads
304 stainless steel and glass-filled nylon frames overmolded with matte black/gray silicone seals alongside jet-black P+R conductive carbon-pill keypads

ISO 9001:2015 Industrial QMS & RoHS / REACH Traceability

Industrial and electronics production runs under ISO 9001:2015 Certificate 21424Q0270R1S (issued 2024-11-13, valid through 2027-11-12; scope covers production of silicone for non-food & medical use) with full raw-lot → molding-batch → shipment traceability. We supply upstream elastomer CoA/SDS sheets and coordinate ~10-day SGS, Intertek, or TÜV finished-part RoHS and REACH compliance reports per project.

View certificate scans and scope →

Three Engineering Interfaces Inside Electronic & Industrial Hardware

Tactile & P+R Control Keymats

Compression-molded silicone keypads with conductive carbon pills, P+R (plastic cap + silicone web) assemblies, and in-house screen printing + protective soft-touch PU coating tuned to PCB switch travel and bezel clearances.

Enclosure Seals & EMI Gaskets

Perimeter housing gaskets, grommets, O-rings, and conductive/EMI shielding seals molded to ±0.05 mm typical precision tolerances (±0.1–0.2 mm general), plus EPDM, NBR, or FKM rubber options when oils or solvents dictate.

Primer Overmolding & Terminal Sleeves

Rugged handheld-scanner boots (30–70 Shore A common) and primer-bonded silicone overmolding onto customer-supplied PC, PP, PA, stainless steel, aluminum, or copper brackets, connectors, and housings.

Four Engineering Package Inputs for Accurate Tooling & Quotes

Seals, keymats, and boots function only inside their mating assembly—share these four details so tooling shrinkage and tolerances match your hardware revision.

2D Tolerance Drawing & 3D Mating Assembly
Provide STEP/IGES files of both the elastomer part and mating bezel, groove, or PCB, plus a 2D PDF marking Critical-to-Quality (CTQ) dimensions, compression stops, and locating pins.
Actuation, Electrical & Media Conditions
Specify key travel, actuation force targets, carbon-pill or metal-dome contact layout, operating temperatures, and exposure to oils, coolants, UV, or outdoor washdowns (to select silicone vs. EPDM/NBR/FKM).
Customer-Supplied Inserts & Primer Overmolding
Insert overmolding uses customer-supplied rigid parts strictly in PC, PP, PA, stainless steel, aluminum, or copper with primer bonding. Confirm plastic glass-fill/heat-deflection specs and supply setup inserts for T1 trials.
Legends, Surface Finishing & Partner Processes
Youbang performs Pantone color compounding, screen printing, and soft-touch protective spray coating in-house; laser etching for backlit legends, epoxy doming, and specialized mold textures are coordinated via vetted partner workshops.
Dimensional measurement equipment
Dimensional measurement equipment

Optical Dimensional Verification & Staged Hardware Fit Checks

Industrial enclosures fail when loose gasket tolerances stack up against injection-molded bezels—our inspection workflow locks revision control from prototype to repeat batches.

2D Vision Metrology & Durometer Control
Critical hole pitches, seal cross-sections, and key-web thicknesses are measured on our 2D optical vision system (×1) alongside Shore A hardness checks across calibrated durometers (×3).
Staged 3D Fit Check to Molded T1 Sign-Off
Verify bezel clearance, port cutouts, and assembly stretch paths on 1–3 free 3D-printed structural samples (buyer pays shipping), then validate tactile snap, sealing compression, and electrical contact on T1 molded samples (7–15 days).
Batch-to-Shipment Document Linkage
Every shipment ties back to incoming compound lot numbers, press parameters, and requested RoHS/REACH or FAI dimensional inspection sheets across 15–30 day typical production lead times.
Read certificate scans and their scope →

Sourcing & Tooling FAQ

Key Answers Before Tooling

Covering CAD readiness, custom MOQ evaluation, free 3D fit checks vs. T1 silicone samples, NDA protection and mold ownership.

Have a part-specific question?

Send your drawing or sample photo directly to Zhou Li’s engineering desk for a 24h DFM reply.

Which finishing operations are performed in-house versus through partner workshops for keypads and covers?

Youbang performs custom Pantone compounding (2 open mixing mills), silk-screen legend printing, and anti-dust soft-touch spray coating in-house at our 4,000 m² Dongguan plant. Laser etching (for backlit icons), epoxy resin doming, and specialized matte/gloss mold texturing are managed through qualified Dongguan partner workshops under our outgoing inspection.

Which rigid insert materials can you overmold for industrial housings, sensors, and rollers?

We overmold LSR and solid HCR silicone onto customer-supplied rigid substrates strictly within our confirmed list—polycarbonate (PC), polypropylene (PP), polyamide (PA), stainless steel, aluminum, and copper—using controlled primer bonding on every insert.

Can you mold non-silicone synthetic rubbers if our assembly contacts fuel, mineral oil, or hydraulic fluid?

Yes. Where silicone swells in hydrocarbon oils or fuels, we also compression-mold EPDM, nitrile rubber (NBR), and fluoroelastomer (FKM/Viton-type) gaskets, grommets, and seals—share your chemical medium and temperature range for elastomer review.

Does a silicone gasket guarantee an IP65 or IP67 rating on its own?

No single loose gasket guarantees an ingress rating—IP performance depends on housing rigidity, screw spacing, groove compression ratio, and complete-enclosure testing. We mold seals to ±0.05 mm typical precision tolerances (±0.1–0.2 mm general) and provide T1 molded samples in 7–15 days so your engineering team can run full-enclosure ingress tests.

B2B Factory Direct · 24h Engineering & Tooling Review

Send Your Keypad, Seal, or Overmolding Assembly Package

Attach 2D/3D CAD files, mating enclosure references, Shore A / elastomer specs, and target order quantities for a 24-hour engineering quotation.

✓ NDA available before CAD exchange✓ Eligible for 1–3 free 3D fit prototypes✓ Paid molds 100% owned by customer

Direct Dongguan Engineering Desk

  • Accepts STEP / IGES / PDF / DWG or sample photos
  • New mold T1 typically 7–15 days · Mass run 15–30 days
  • Direct Tel / WeChat: +86 185 6655 6911 (Zhou Li)